FIELDPIECE01

Feature-packed for optimum performance, with the Fieldpiece Clamp-On Meter, you'll get the most out of the one meter you need to carry!

Features:
Non-contact Voltage - Loud beeper and bright LED indicate the NCV tab is near AC voltages greater than 24V
Temperature - Thermocouple plugs in directly for accurate readings, even in fast changing environments
Microamps - For flame rectifier diode tests
Capacitance - For motor-run and motor-start capacitors And More
Hi-voltage indicator you can't miss--both LED and beeper turn on to indicate you've touched a potentially dangerous voltage
Continuity indicated by LED and beeper
MAX hold automatically holds reading so you can look at the meter after you've disconnected
Low ohms ranges for motor windings and mid range for thermistors
Amps AC resolution to 0.01A for heat anticipator circuit (20A range). Up to 200AAC with 0.1V resolution (200A range)
DC to 0.01V resolution (20V range)
Auto-power off to extend battery life

Test Lead Solutions:
Probe storage in the back. Just snap them in
Single test lead holder for easy and safe voltage testing
Silicone test leads remain flexible in cold weather, withstand caustic chemicals, and work well in temperatures that will melt vinyl leads
Convenient lead storage. Wrap test leads through clamp to keep the wires out of the way
You can even leave them right there when you test amps

Click Here For Specification

FIELDPIECE02

The Fieldpiece Digital Multimeter with Phase Rotation function identifies phase sequence for 3 phase motor installations.

Features:
Works with all Fieldpiece accessory heads using Fieldpiece Deluxe silicone leads (ADLS2) or Fieldpiece Head Adapter Handle (AHDL1)
Capacitance for motor start/run capacitors
High voltage warning (LCD and beeper)
Microamps for flame rectifier diode circuit
Amps to 10AAC through meter, to 300AAC with clamp
Frequency for variable frequency motor drives
MOV transient protection
Valox housing
”O” ring seals and gaskets to keep contamination out
High voltage fuses
Rubber holster

Click Here For Specification

FIELDPIECE03

Fieldpiece Digital Stick Meter HS33

All of Fieldpiece's accessory heads work with the Fieldpiece Stick Meter. With the appropriate accessory head, this meter can measure the following parameters: AC amps, RH%, wet bulb temperature, air temperature, dew point, carbon monoxide, dual temperature, non contact (IR) temperature, air velocity, gas pressure, static pressure, vacuum, milliamps, microamps, and carbon dioxide. Accessory heads can also be connected to the meter using the removable-tip test leads for “remote” testing.

Features:
Removable probe tips for connection to accessory heads
Attach detachable probe tip directly into jack for easy and safe voltage testing
Silicone wire test leads remain flexible in cold weather, withstand caustic chemicals, and work well in temperatures that will melt vinyl leads
Leads conveniently wrap around meter
Rugged rubberized case with built-in magnetic hanger
300AAC clamp head
Deluxe silicone rubber test leads with storage on the back
Alligator clips
K-type thermocouple

Click Here For Specification

FIELDPIECE04

Fieldpiece Stick Meter with Auto Ranging HS35

The Fieldpiece Stick Meter with Auto Ranging tests microamps for flame rectifier diode tests and the ability to measure frequency.
All of Fieldpiece's accessory heads work with the Fieldpiece Stick Meter. With the appropriate accessory head, this meter can measure the following parameters: AC amps, RH%, wet bulb temperature, air temperature, dew point, carbon monoxide, dual temperature, non contact (IR) temperature, air velocity, gas pressure, static pressure, vacuum, milliamps, microamps, and carbon dioxide.

Features:
Digital Multimeter
K-type thermocouple
Capacitance
Non-contact voltage sensing
Silicone rubber test leads with storage on the back
High-voltage indicator
Current clamp head
Rugged rubberized case with built-in magnetic hanger
Alligator clips
LED and a beeper to indicate continuity

Click Here For Specification

Spec Summary

FIELDPIECE05

Fieldpiece Stick Meter with True RMS & Backlight HS36

All of Fieldpiece's accessory heads work with the Fieldpiece Stick Meter. With the appropriate accessory head, this meter can measure the following parameters: AC amps, RH%, wet bulb temperature, air temperature, dew point, carbon monoxide, dual temperature, non contact (IR) temperature, air velocity, gas pressure, static pressure, vacuum, milliamps, microamps, and carbon dioxide.

Features:
True RMS
Backlit
Digital Multimeter
K-type thermocouple
Capacitance
Non-contact voltage sensing
Silicone rubber test leads with storage on the back
High-voltage indicator
Current clamp head
Rugged rubberized case with built-in magnetic hanger
Alligator clips
LED and a beeper to indicate continuity

Click Here For Specification

Spec Summary

FIELDPIECE06

The Fieldpiece Electronic Handle converts any Fieldpiece accessory head into a stand alone instrument

The Fieldpiece Electronic Handle has ranges to display the parameter without forcing you to move decimal points in your head while still providing 0.1mV resolution.

Features:
Works with all Fieldpiece accessory heads
200mV and 2000mV, AC and DC ranges for maximum readings to 1999 and resolution as good as 0.1
MIN/MAX to record highest and lowest readings
Data Hold button
Minimal circuitry for increased reliability
Overload Protection
Rugged mechanical design
Standard 9V battery

Click Here For Specification

Spec Summary

FIELDPIECE07

Fieldpiece Carbon Monoxide Accessory Head ACM3

The Fieldpiece Carbon Monoxide Accessory Head measures CO in air and finds CO sources

The Fieldpiece Carbon Monoxide Accessory Head enables most digital multimeters to measure low levels of carbon monoxide in parts per million (PPM). It is intended to measure levels of CO in still ambient air. In many cases, it can pinpoint sources of CO. It uses a catalytic chemical sensor that consumes no chemicals. The most pratical application is to determine if the indoor CO levels are higher than outdooor levels and to determine the source.

Features:
Fast enough to locate CO source in “walk-around” test
Three pin sensor for better performance
Long battery life
Auto-off can be disabled for data logging
Select averaging or normal for smoothing or fast response to change
Rugged mechanical design
Standard 9V battery

Click Here For Specification

Spec Summary:

Range:	0 to 1000PPM (2000PPM with 5 minute max exposure time).
Initial accuracy:	0-15ppm ±5% reading ±1 ppm after zeroing; 15-35ppm ±5% reading ±2 ppm after zeroing; 0-1000ppm ±5% reading ±5 ppm after zeroing.
Response time:	<70sec to 90% of reading.
Operating temperature:	32 to 105ºF
Sensor type:	Electrochemical (specific to CO)
Power:	Single standard 9-volt battery
Battery Life:	200 hours

Note: The Fieldpiece Carbon Monoxide Accessory Head is required to be used with the Electronic Handle (EHDL1).

Optional: ACMP3 Pump see specifications for details.

FIELDPIECE08

Fieldpiece Current Clamp On Accessory Head ACH4

Use your digital multimeter, data logger, or handle to measure parameters needed by HVAC/R technicians. Fieldpiece accessories work with meters that have mV (AC and DC) ranges and industry standard input jacks. Use the Fieldpiece deluxe test leads or the convenient AHDL1 adapter handle to connect any accessory head to most digital multimeters. The ACH4 works with the Fieldpiece "Stick meter, EHDL1 Electronic Handle, DL2 Data Logger, or any digital multimeter (with mVAC range) connected by Fieldpiece ADLS2 leads or AHDL1.
USE IT YOUR WAY..

For most heads, set your meter to mVDC and read the LCD directly.

Features:
Use for remote testing with the Fieldpiece Head Adapter Handle (AHDL1) Ergonomic shape and small size fits in hard to reach places
Rugged mechanical design
Battery not required

Click Here For Specification

Spec Summary:

FIELDPIECE09

Fieldpiece Digital Data Logger with PC Software DL2

The Fieldpiece Digital Data Logger with PC Software records measurement, time, and parameter

The Fieldpiece Data Logger with PC Software records mV signals from any Fieldpiece accessory head automatically or manually. For automatic measurements, using the internal real time clock, you can program start and stop times and time between measurements.

You can measure the air velocity on nine points of a grill and then easily display average, or make five consecutive readings as you survey a problem, labeling each using the PARA function. The data logger will record the measurement, the time of the measurement, and the PARA label you assigned.

Use scroll buttons and MIN/MAX/AVG button to see the data on the LCD or "dump" the data to a computer for use with most spreadsheet or database programs. It's real easy to do and will work with a computer that has a COM port.

Features:
Records and separates multiple sets of data up to 20,000 data points Battery life greater than one month
Internal real time clock
Record automatically or manually
Use with any Fieldpiece accessory head
Display readings on LCD or "dump" data to computer
Includes PC utility software, operators manual, and cables that connect your DL2 to your computer

Click Here For Specification

Spec Summary

FIELDPIECE10

Fieldpiece Infrared Thermometer Accessory Head ATIR3

Fieldpiece Infrared Thermometer Accessory Head measures temperature by collecting infrared energy emitted by target and converting it to a mVDC signal for direct current reading on any meter with mV ranges. Non-contact infrared temperature measurement works best if you cannot touch the test point or if you are looking fot the hottest or coldest area. IR temperature readings can vary with angle, and how reflective the surface is.

The Fieldpiece Infrared Thermometer Accessory Head is required to be used with the Electronic Handle (EHDL1).

Features:
8:1 Distance to spot ratio
Non-contact (Infrared) surface temperature head with laser sight
Select ºF or ºC
Works with the Fieldpiece stick meter HS35), data logger (DL2), and the electronic handle (EHDL1)
Rugged mechanical design

Click Here For Specification

Spec Summary

FIELDPIECE11

Fieldpiece Infrared Thermometer Accessory Head ATIR3

The Fieldpiece Manometer Accessory Head measures gas pressure and has resolution low enough for static pressure. It measures pressure, both positive and negative, from -20"WC (water column) to +20"WC. When the 2"WC range is selected, 0.01"WC resolution is obtained with a standard 2000 count digital multimeter. The Fieldpiece Manometer Accessory Head snaps into the Fieldpiece stick meter (HS35)or the electronic handle (EHDL1) for a direct readout. Connect to any digital multimeter with industry standard jacks and a mVDC range with 0.1 resolution using the adapter handle AHDL1) for a direct readout.

Features:
Maximum 20" WC (water column) for gas pressure
0.01" WC resolution for static pressure
Manual zero-set for comparing two pressures
Includes tube and adapter for gas pressure measurement
Auto-off can be disabled for data logging
Low battery indicator
Rugged mechanical design
Standard 9V battery

Click Here For Specification

Spec Summary

Note:The Fieldpiece Manometer Accessory Head is required to be used with the Electronic Handle (EHDL1).

FIELDPIECE12

Fieldpiece Milliamps and Microamp Accessory Head AUA2

Fieldpiece Milliamps and Microamp Accessory Head measures milliamps and microamps for flame diode tests

The Fieldpiece Milliamps and Microamp Accessory Head coverts microamps for (rectifier diode) and milliamps to a mV signal for direct current reading on any meter with mV ranges. For resolution of 0.1 micro/milliamps use a meter that displays 0.1 mV. The Fieldpiece Milliamps and Microamp Accessory Head along with the included quick connect and mini-plug adapters converts the Fieldpiece stick meter (HS33), data logger (DL2) and electronic handle (EHDL1) to a one-piece flame rectifier diode tester.

Features:
Includes flame diode adapter kit
Inludes mini-plug adapters
Measures 4 to 20mA control circuits

Click Here For Specification

Spec Summary

Note: The Fieldpiece Milliamps and Microamp Accessory Head is required to be used with the Electronic Handle (EHDL1).

FIELDPIECE13

Fieldpiece Optical Laser Tachometer SRPM1

Fieldpiece Optical Laser Tachometer measures RPM without contact
The Fieldpiece Optical Laser Tachometer is a stand-alone device that senses the passage of reflective markings on a rotating fan or shaft in order to determine the target's rotational rate. When the laser is pointed at the included reflector strip, the three-digit LCD display indicates the RPM. RPM is measured when the laser beam is interrupted by the revolution of the target. The laser beam stays narrow, even over long distances.

Features:
Works up to four feet from rotating fan or shaft
Counts reflected laser light pulses
Reads out in RPM or total counts
Stores last reading, min, and max
Included: Reflector Strips

Click Here For Specification

Spec Summary

FIELDPIECE14

Fieldpiece Pocket Digital Thermometer SPK1

Fieldpiece Pocket Digital Thermometer easily fits in a shirt pocket
The Fieldpiece Pocket Knife Style Digital Thermometer folds in and out just like a pocket knife. The 180° of probe rotation allows for various applications. Poke it through a soft duct or hang it in a grille.

Features:
Easily hangs from vent, register, or thermostat
Pull out rod just like you would a pocketknife
Grooves hold rod at any angle
Easily hangs from flex duct
Rod folds away; no sleeve to lose
°C or °F
MIN/MAX function
Hold function
Auto off after 10 minutes

Click Here For Specification

Spec Summary

FIELDPIECE15

Fieldpiece Sling Psychrometer Accessory Head ARH4

The Fieldpiece Sling Psychrometer Accessory Head calculates wet bulb and dew point
The Fieldpiece Sling Psychrometer Accessory Head measures air temperature and RH% and displays wet bulb and dew point. This accessory head enables digital multimeters to measure humidity and temperature of air.

Features:
Contains lookup charts to calculate wet bulb and dew point
Auto-off can be disabled for data logging
Select ºF or ºC
Rugged mechanical design
Standard 9V battery

Click Here For Specification

Spec Summary

Note: The Fieldpiece Sling Psychrometer Accessory Head is required to be used with the Electronic Handle (EHDL1).

FIELDPIECE16

Fieldpiece Vacuum Gauge Accessory Head AVG2

The Fieldpiece Vacuum Gauge Accessory Head measures vacuum from 50 to 2000 microns of mercury

The Fieldpiece Vacuum Gauge Accessory Head displays pressure in microns in steps of 1 microns. Has pump down indication showing progress from atmospheric pressure.

You'll know your vacuum pump is working and you are drawing a good vacuum as you go from atmospheric to deep vacuum. Set your meter to VDC and see the display drop from over 3.0 to under 2.0 as the pressure goes from atmospheric to under 200 microns. Then switch to a mVDC range to display microns and see pressure in microns of mercury to a ±1 micron resolution.

Features:
Range: 50 to 2000 microns of mercury
Resolution: 1 micron of mercury
Pump down indication: when pumping down from atmospheric pressure to 2000 microns, output of head goes from over 3VDC to 2VDC
Straight-in access to sensor for easy cleaning
Fitting: 1/4" flared brass fitting (male)
Accuracy (@~75ºF): ±10%, 0-1000 microns of mercury
Auto-off can be disabled for data logging
"T" for inline vacuum testing

Click Here For Specification

Spec Summary

FIELDPIECE17

Fieldpiece Vane Anemometer Accessory Head w/ Temperature AAV3

The Fieldpiece Vane Anemometer Accessory Head measures air velocity from 60 to 5900 ft/min

The Fieldpiece Anemometer Accessory Head with Temperature measures air velocity and temperature of the moving air. You can estimate CFM by multiplying the average air velocity times the size of the opening expressed in square feet. The easiest way to get the average air velocity is to use the data logger (DL2). Take nine readings (in 3 by 3 pattern) over the grill and the data logger will average the readings. The Electronic Handle (EHDL1) is required to work with all digital multimeters with mV ranges.

Features:
Using the Fieldpiece Head Adapter Handle (AHDL1) you can display parameters directly on digital multimeters set on mVDC scale
Temperature Measurement Range: -4ºF to 140ºF
Works with the Fieldpiece stick meters (HS35), data logger (DL2) and electronic handle (EHDL1)
Ball bearing moving vane
Auto-off to save battery life

Click Here For Specification

Spec Summary

FIELDPIECE18

Fieldpiece K-Type Thermometer Accessory Head ATH4

The Fieldpiece K-Type Thermometer Accessory Head has two k-type thermocouple inputs. The Fieldpiece K-Type Thermometer Accessory Head converts temperature sensed by the thermocouples to mVDC range. Set the meter to mVDC and read the temperature measurement directly.

Features:
Display T1, T2, or T1-T2
Field calibration for ± 1ºF accuracy
Displays ºF directly at 0.1ºF resolution on DMM with 0.1mVDC resolution
Select ºF or ºC
Converts from -50ºF to 1800ºF
Slide on stick meter (HS35) or adapter handle (AHDL1)
Includes two “wrap tab” thermocouples plus velcro straps (Thermocouples insulated to 400ºF)
Auto-off can be disabled for data logging

Click Here For Specification

Spec Summary

Note: The Fieldpiece K-Type Thermometer Accessory Head is required to be used with the Electronic Handle (EHDL1).

FIELDPIECE19

Fieldpiece Head Adapter AHDL1

Fieldpiece Accessory Head Adapter provides a convenient way to connect a Fieldpiece accessory

Features:
Fieldpiece Accessory Head Adapter connects any Fieldpiece accessory head to any digital multimeter with industry standard jacks
Fieldpiece Accessory Head Adapter's handle makes it easier to use an accessory head

FIELDPIECE20

Fieldpiece Deluxe Silicone Leads fit all Fieldpiece meters and other meters with industry standard jacks

Features:
High copper stranding, silicone insulated test leads
Basket style strain relief
Fit in test lead holders on back of HS series stick meters (HS35) & (HS33)
Removable probe tips

FIELDPIECE21

Fieldpiece Dual Alligator Clip Cables ADA2

Fieldpiece Dual Alligator Clip Cables fit all meters with industry standard jacks

Three feet of red and black vinyl insulated cable with small alligator clips on the end.

FIELDPIECE22

Fieldpiece K-type Thermocouple ATA1

Fieldpiece K-type Thermocouple is used with any meter using the K-type design

Includes alligator clips so that you can just clip to the spot you're testing. You no longer need three hands to do your job. All three pipe clamps are redesigned to provide faster and more accurate pipe temperatures.

Features:
Bead type with alligator clips
Maximum Temperature - 400ºF

Click Here For Specification

FIELDPIECE23

Fieldpiece High Temperature K-type Thermocouple ATAF1

Fieldpiece High Temperature K-type Thermocouple is used with any meter using the K-type design

Includes alligator clips so that you can just clip to the spot you're testing. You no longer need three hands to do your job. All three pipe clamps are redesigned to provide faster and more accurate pipe temperatures.

Features:
Bead type with alligator clips
Maximum Temperature - 900ºF

Click Here For Specification

FIELDPIECE24

Fieldpiece K-type Thermocouple (Wet Bulb) ATWB1

Fieldpiece K-type Thermocouple is used with any meter using the K-type design

Includes alligator clips so that you can just clip to the spot you're testing. You no longer need three hands to do your job. All three pipe clamps are redesigned to provide faster and more accurate pipe temperatures.

Features:
Wet bulb (sock) with alligator clips
Maximum Temperature - 150ºF

Click Here For Specification

FIELDPIECE25

Fieldpiece K-type Thermocouple For Fluids ATF1

Fieldpiece K-type Thermocouple is used with any meter using the K-type design

Features:
6" stainless tip designed for fluids (1500°F tip)

FIELDPIECE26

Fieldpiece Bead Tip K-Type Standard Thermocouple ATB1

Fieldpiece K-type Thermocouple is used with any meter using the K-type design. The ATB1 thermocouple can be used continously to take temperature readings up to 400°F and a one time use of 482°F.

The velcro allows the user to strap the ATB1 to a pipe, allowing the user to take hands free, more accurate measurement. The ATB1 also comes with a wrap tab making it easy to wind and store the thermocouple.

Click Here For Specification

FIELDPIECE27

Fieldpiece Small Pipe Clamp ATC1

K-thermocouple, small pipe clamp can be used to take temperature of pipes or any other cylindrical surface under 1 3/3" OD. The ATC1 can greatly facilitate taking a superheat or subcooling measurement on most residential and commercial refrigeration appliances or air conditioners. The ATC1 can even take the temperature of pipes that are fixed to walls or other surfaces. The ATC1 can be used with any thermometer which accepts a K-Type thermocouple.

Click Here For Specification

FIELDPIECE28

Fieldpiece K-type Thermocouple Premium Pipe Clamp ATC3

Use Fieldpiece K-type thermocouples with any meter using the K-type design. The new line of thermocouples (ATA1, ATAF1, ATWB1) include alligator clips so that you can just clip to the spot you’re testing. You no longer need three hands to do your job. All three pipe clamps are redesigned to provide faster and more accurate pipe temperatures. Wrap the lead wire around the tab for convenient lead storage.
Max ºF (tip)=300

K-thermocouple, small pipe clamp can be used to take temperature of pipes or any other cylindrical surface under 1 3/3" OD. The ATC3 can greatly facilitate taking a superheat or subcooling measurement on most residential and commercial refrigeration appliances or air conditioners. The ATC3 can even take the temperature of pipes that are fixed to walls or other surfaces. The ATC3 can be used with any thermometer which accepts a K-Type thermocouple.

Click Here For Specification

FIELDPIECE30

Fieldpiece 4.5" piercing probe with handle ATR1

Use Fieldpiece K-type thermocouples with any meter using the K-type design. The new line of thermocouples (ATA1, ATAF1, ATWB1) include alligator clips so that you can just clip to the spot you’re testing. You no longer need three hands to do your job. Both pipe clamps are redesigned to provide faster and more accurate pipe temperatures.

1500 Max ºF (probe)

FIELDPIECE31

Fieldpiece Disk type for grilles ATS1

Use Fieldpiece K-type thermocouples with any meter using the K-type design. The new line of thermocouples (ATA1, ATAF1, ATWB1) include alligator clips so that you can just clip to the spot you’re testing. You no longer need three hands to do your job. Both pipe clamps are redesigned to provide faster and more accurate pipe temperatures.

FIELDPIECE32

ADK7 Kit Contains ADLS2 silicone test leads, removable probe tips, and ASA2 alligator clips for grounding.

FIELDPIECE34

Fieldpiece A/C Line Splitter ALS1

The ALS1 line splitter seperates the two 120VAC current carrying wires, enabling the user to easily measure current with any AC current clamp meter.

Features:
Use the ALS1 with clamp meter
X10 loop for accurate low current measurements.
Three wire plug for grounded circut.
Up to 15AAC load.
Contacts for easy voltage measurements

Click Here For Specification

FIELDPIECE36

Fieldpiece Gun Style IR Thermometer SIG1

Features:
Field of view 10:1.
Blue backlight.
Laser guide.
Protective lens cap.
Faster than thermistor
based thermometers.
Range: -22°F to 1022°F.
Auto off

Click Here For Specification

FIELDPIECE37

Fieldpiece Pen-Type IR Thermometer & LED Flashlight SIL2

The SIL2 is a sleek pen-type IR thermometer with an LED flashlight. It is